Skip to content

Toyota Sienna 2001 Key Fob & Car Keys

Keys that fit the 1999–2003 Toyota Sienna: smart keys, remote keys and transponder keys, 3 or 4 buttons, FCC ID GQ43VT14T, 4C chip, 315 MHz. 5 compatible keys, remotes & shells (genuine and aftermarket) available for the 2001 Toyota Sienna.

Last updated: 15 November 2026

Key specifications for the Toyota Sienna 1999–2003

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz
Buttons
3- and 4-button
Transponder chip
4C
Blade profile
TOY43
Part numbers
89742-AA030
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Toyota parts catalogue, with the specifications on each listing. Every remote listed for the Toyota Sienna 1999–2003 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Toyota Sienna 2001 key

Key with a blade (regular or flip)

2 tools list this key. 1 of them list all keys lost.

  • Launch X-431 IMMO
    • Add key
    • All keys lost
  • OBDSTAR Key Master G3
    • Add key
    • Remote

All keys lost is listed by Launch X-431 IMMO. OBDSTAR Key Master G3 lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: working master key (not the grey valet key), new 4C key cut to the car

  1. Check the customer's key is a master: insert it and the security light goes out at once (a valet key keeps it on for about 2 s).
  2. Close the doors. With no key in the ignition, press and release the accelerator and the brake together once.
  3. Insert the master key without turning it. Within 15 s press and release the accelerator 5 times.
  4. Within 20 s press and release the brake 6 times, then remove the master key.
  5. Within 10 s insert the new key without turning it and press the accelerator once. The security light starts to flash.
  6. Wait about 1 minute (up to 80 s) until the light stops flashing: the key is learned. For one more key, insert it within 10 s and press the accelerator once again.
  7. Remove the last key and press the brake once to finish. Test that every key starts the engine.
Watch out: Timing is strict: if a window is missed, take the key out and start again from step 2. Without a master key this route does not work: all keys lost on a 4C car is an ECU / immobilizer data job. The memory holds a limited number of keys (7 on most of these cars, 3 on the Prius and the 2001-2002 Sequoia); if the new key will not learn, the memory may be full. For 4C cars only: 4D (dot) keys from 2003-2004 onward need a tool.

Key type not stated by the list

2 tools list this key. 2 of them list all keys lost.

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Every remote to be programmed, A key that fits the ignition

  1. Start with the key out, the driver's door open and unlocked, and every other door closed.
  2. Insert the key without turning it and pull it out.
  3. Within 40 seconds, work the driver's power lock switch 5 times LOCK then UNLOCK, starting with LOCK, about one cycle per second, then close and open the driver's door.
  4. Within the next 40 seconds, do 5 more LOCK / UNLOCK cycles at the same pace, then insert the key in the ignition.
  5. Turn the ignition to ON without starting and back to OFF, two times, then remove the key.
  6. Within 3 seconds the locks cycle by themselves: the car is in programming mode. If they do not, start again from step 1.
  7. Within 40 seconds, hold LOCK and UNLOCK together on the remote for 1 second.
  8. Right after releasing them, hold LOCK alone for 2 seconds.
  9. Within 3 seconds the locks cycle once: the remote is accepted. No cycle or two cycles mean it was not accepted, repeat steps 7 and 8.
  10. Repeat steps 7 to 9 for each extra remote.
  11. Close the driver's door to end programming.
Watch out: Each block of steps 3 and 4 and the remote step must be done within 40 seconds.

When the key changed

Smart key (push to start)

  • 2011 - 2020Chip: DST80315 MHzFCC: HYQ14ADR(US / Canada cars)Push-start trims only
  • 2021 - 2026Chip: 8A315 MHzFCC: HYQ14FBX(US / Canada cars)Page BA key

Key with a blade (regular or flip)

  • 1998 - 2003This yearChip: 4CBlade: TOY43
  • 2004 - 2010Chip: 4D-67Blade: TOY43(US / Canada cars)Overlap years may be 4D-67 or G; G is stamped on the blade
  • 2011 - 2014Chip: GBlade: TOY43(US / Canada cars)
  • 2015 - 2019Chip: H (8A)Blade: TOY43(US / Canada cars)

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Toyota Sienna 1999–2003?

5 listings fit the Toyota Sienna 1999–2003: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Toyota Sienna 1999–2003 remote use?

Every remote listed for the Toyota Sienna 1999–2003 transmits on 315 MHz.

Which transponder chip does the Toyota Sienna 1999–2003 key use?

The listings for this car carry: 4C. Check the chip in each listing's specifications.

Which FCC IDs do Toyota Sienna 1999–2003 remotes carry?

The remotes listed for this car carry FCC ID GQ43VT14T. Match it with the FCC ID printed on your original remote.

Which blade profile does the Toyota Sienna 1999–2003 key use?

The blades listed for this car: TOY43.

Which tools program a Toyota Sienna 1999–2003 key?

The tool makers' coverage lists name Launch X-431 IMMO, OBDSTAR Key Master G3, Xhorse MINI OBD Tool (FT-OBD) and Autel IM608 II / IM608 Pro II for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Toyota Sienna 1999–2003 remote be programmed without a tool?

The remote is programmed on the car, without a tool.