Skip to content
  1. Home
  2. Auto Key Programming
  3. Adapters
  4. NXP Killer Adapter MCKB005 for Toyota 2019-2021 Smart Keys - Solder-Free HYQ14FBN
NXP Killer Adapter MCKB005 for Toyota 2019-2021 Smart Keys - Solder-Free HYQ14FBN

NXP Killer Adapter MCKB005 for Toyota 2019-2021 Smart Keys - Solder-Free HYQ14FBN

Genuine new

SKU: B02285

$9.83
AED  35.00
  • 312-433 MHzFrequency
  • ID4ATransponder

In Stock

Specifications

Solder-free PCB adapter MCKB005 for the NXP Killer tool, cut for Toyota 2019-2021 smart key boards.

Money-back protection:
Claim a refund if your order doesn't ship, is missing, or arrives with product issues
Genuine · New

NXP Killer Solder-Free Adapter MCKB005 for Toyota 2019-2021 Smart Keys

Solder-free PCB adapter · MCKB005 · ID 4A · 312 MHz, 315 MHz and 433 MHz across the market variants · HYQ14FBN · Toyota

MCKB005
Adapter model
Solder-free
Connection method
ID 4A
Target key chip
2019-2021
Model years

⭐ This is MCKB005, the solder-free contact board the NXP Killer uses to reach the Toyota smart key boards listed below. It clamps onto the PCB and bridges the five marked contacts (MSCL, MSDA, VCC, GND and WAKE), so the chip stays where it is for the whole job. The boards it serves carry ID 4A at 312 MHz, 315 MHz and 433 MHz across the market variants. Look for HYQ14FBN on the original board. Sold as a workshop accessory, it carries no electronics of its own and needs the NXP Killer to do any work.

⚙️ Key features

Board-specific fit

Cut for one key board footprint, so the contacts land where they should on the first attempt.

Bench-speed access

Working with the NXP Killer, a read runs around 20 seconds and a write around 30 seconds.

Protects the board

No iron on the pads means no lifted copper and no heat-damaged transponder.

Held under spring pressure

The clamp keeps steady contact through the whole read and write cycle without a third hand.

💎 Benefits

Pays back over jobs

One adapter serves an unlimited number of keys that share the same board layout.

Lower skill barrier

A technician who does not solder to micro pitch can still run the job cleanly.

Wider service list

Adding one board footprint widens what the counter can quote on without new machinery.

Fewer comebacks

A board that was never heated behaves the same after the job as it did before it.

👥 Who it's for

Automotive locksmiths

Bench cloning as part of a spare-key or duplicate service.

Key shops and counter trade

Walk-in duplicate work without sending the board out.

Dealers and garages

In-house spare keys for used stock before the car goes on the forecourt.

Fleet workshops

Keeping spare keys on the shelf for vehicles that run every day.

🚗 Compatible vehicles

🚘 TOYOTA · 2019-2021
Corolla
Corolla Hybrid
Before ordering, open the key and match the board layout plus HYQ14FBN or B2U2K2R or a listed part number against this adapter. A make and model share several board revisions, and only the layout decides the fit.

📦 What's included

✅ IN THE BOX

✔ 1 x MCKB005 solder-free PCB adapter

❌ NOT INCLUDED

✘ NXP Killer programmer - ordered separately

✘ Other MCKB adapters - each board footprint needs its own

✘ Smart key, transponder or emergency blade - source separately

✘ Cable and power supply - shipped with the NXP Killer tool

📋 Specifications

🔌 ADAPTER
Model
MCKB005
Type
Solder-free PCB adapter
Connection
Five-pin header
Contact points
MSCL, MSDA, VCC, GND and WAKE
Works with
NXP Killer / Super NXP Killer
🔐 TARGET KEY BOARD
Chip family
NXP NCF29XX
Transponder
ID 4A
Frequency
312 MHz, 315 MHz and 433 MHz across the market variants
Host key buttons
3 and 4 button
Model years
2019-2021
Board marking
B2U2K2R
🔢 KEY BOARD REFERENCES
FCC ID
HYQ14FBN
Part number
8990H-12010
Part number
8990H-02030
📦 PHYSICAL
Weight
100 g
Condition
Genuine · New
Quantity
1 piece

Frequently Asked Questions

Common questions about this product

MCKB005 is a solder-free PCB adapter that links a Toyota smart key board to the NXP Killer programmer. It makes contact on the key board itself, so the transponder is read and written without desoldering the chip. Nothing on the key board is heated or removed.
No. MCKB005 is a passive accessory that only carries signals between the key board and the programmer. You need the NXP Killer device itself to run any read, write or reset operation on the key. Each board footprint needs its own MCKB adapter.
MCKB005 fits the Toyota smart key boards used on Corolla, Corolla Hybrid, model years 2019-2021. Match the board layout against the adapter before ordering. One model can ship more than one key board revision. Send us a photo of the opened key if you are unsure.
You need one adapter per board footprint, not one per car. MCKB005 covers a single key board layout, and other keys in the same range use different MCKB adapters. A second footprint means a second adapter. Check the layout before you order a second one.
The boards MCKB005 serves carry ID 4A and run at 312 MHz, 315 MHz and 433 MHz across the market variants. The NXP Killer reads and writes that transponder directly through the adapter. The model name alone does not settle the variant.
No heat is applied, which is the whole point. Soldering onto a smart key board risks lifting the copper pads or cooking the transponder. MCKB005 seats on the existing contact points instead. Lifted copper is the usual cost of the old method.
Cloning a board through MCKB005 with the NXP Killer copies the original transponder data, so the duplicate is accepted without a fresh registration on the vehicle. The board is read, written and refitted in one session. Keep the original board until the duplicate is tested.
One MCKB005 adapter. The NXP Killer programmer, its cable and power supply, and any other MCKB adapters are all sold separately. No key, chip or blade is supplied with it. The cable and supply ship with the tool itself.