Skip to content

Buick Lucerne 2007 Key Fob & Car Keys

Keys that fit the 2006–2011 Buick Lucerne: transponder keys, ID46 (HITAG 2) or NXP PCF7936AA chip. 3 compatible keys, remotes & shells (genuine and aftermarket) available for the 2007 Buick Lucerne.

Last updated: 15 November 2026

Key specifications for the Buick Lucerne 2006–2011

Key types
transponder keys, key shells and key blanks
Transponder chip
ID46 (HITAG 2) · NXP PCF7936AA

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Buick parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Buick Lucerne 2007 key

Key with a blade (regular or flip)

2 tools list this key. 1 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • Launch X-431 IMMO
    • Add key

All keys lost is listed by OBDSTAR Key Master G3. Launch X-431 IMMO lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working key, new key cut to the vehicle

  1. Cut the new key to the vehicle; have one key that already starts it.
  2. Put the working key in the ignition and turn it to ON/RUN (or start the engine), then turn it to LOCK/OFF and remove it.
  3. Within five seconds insert the new key and turn it to ON/RUN.
  4. The security light goes off when the key is learned (this can be too fast to notice).
  5. Start the engine with the new key; for each further key repeat from step 2.
Watch out: Adds only; never erases keys. Up to 10 keys (owner's manual and service manual).
All keys lost - on the car(US / Canada cars)

Needs: new key cut to the vehicle, 30 minutes

  1. Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn OFF, then start the engine with this key: it is learned and every previously known key is erased.
  6. Learn the remaining keys with the add-key procedure.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer.

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: the key, all remotes to be kept

  1. Bring every remote the customer keeps; all of them must be matched in the same session.
  2. Key in, ignition ON, transmission in Park.
  3. With DIC buttons: press the vehicle information button until RELEARN REMOTE KEY shows, then press set/reset until REMOTE KEY LEARNING ACTIVE shows.
  4. Without DIC buttons: press the trip odometer reset stem until RELEARN REMOTE KEY shows, then hold it about 3 seconds until REMOTE KEY LEARNING ACTIVE shows.
  5. Hold lock and unlock together on the first remote for about 15 seconds; a chime confirms it.
  6. Repeat step 5 for each remote (up to eight).
  7. Turn the ignition to LOCK/OFF to leave, then test all remotes.
Watch out: Remotes not matched in this session stop working. On memory-seat vehicles the first remote matched becomes driver 1, the second driver 2.

When the key changed

Key with a blade (regular or flip)

  • 2006 - 2011This yearChip: ID46Blade: B111(US / Canada cars)Circle Plus key; separate remote.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Buick Lucerne 2006–2011?

3 listings fit the Buick Lucerne 2006–2011: transponder keys, key shells and key blanks. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which transponder chip does the Buick Lucerne 2006–2011 key use?

The listings for this car carry: ID46 (HITAG 2) · NXP PCF7936AA. Check the chip in each listing's specifications.

Which tools program a Buick Lucerne 2006–2011 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Buick Lucerne 2006–2011 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.