Skip to content

Chrysler 300 2008 Key Fob & Car Keys

Keys that fit the 2008 Chrysler 300: smart keys, remote keys and transponder keys, 2, 3 or 4 buttons, FCC ID IYZC01C, M3N5WY783X or K0BDT04A, ID46 (HITAG 2) or PCF7941 chip, 315 MHz or 433 MHz. 16 compatible keys, remotes & shells (genuine and aftermarket) available for the 2008 Chrysler 300.

Last updated: 15 November 2026

Key specifications for the Chrysler 300 2008

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
2-, 3-, 4-, 5- and 7-button
Transponder chip
ID46 (HITAG 2) · PCF7941 · NXP PCF7936AA
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chrysler parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chrysler 300 2008 key

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    PIN read function

Programming steps

Add key - on the car(US / Canada cars)

Needs: Two working key fobiks available, two working programmed key fobiks, the new key fobik

  1. Insert the first working key fobik and turn the ignition ON for at least 3 but no more than 15 seconds.
  2. Turn to LOCK/OFF and pull the key fobik out.
  3. Within 15 seconds, insert the second working key fobik and turn ON. After 10 seconds a chime may sound and the Vehicle Security Light starts flashing.
  4. Turn to LOCK/OFF and pull the key fobik out.
  5. Within 60 seconds, insert the new key fobik and turn ON.
  6. After 10 seconds a single chime sounds, the Vehicle Security Light stops flashing, stays on for 3 seconds and goes out: the new key fobik is programmed.
  7. Repeat the whole procedure for each extra key fobik.
Watch out: The first key must stay ON 3 to 15 seconds, the second key goes in within 15 seconds and the new key within 60 seconds. Up to 8 keys can be programmed. The remote (RKE) part of the new fobik is programmed in the same procedure.
Add key - on the car(US / Canada cars)

Needs: two working Fobiks, new blank Fobik

  1. Have the new (never programmed) Fobik ready; have two different Fobiks that already start the vehicle.
  2. Insert the first working Fobik and turn to ON for at least 3 but no more than 15 seconds, then turn OFF and remove it.
  3. Within 15 seconds insert the second working Fobik and turn to ON; after about 10 seconds a chime sounds and the security light flashes. Turn OFF and remove it.
  4. Within 60 seconds (stay under 50 to be safe) insert the new blank Fobik and turn to ON.
  5. After about 10 seconds a single chime sounds, the light stops flashing, stays on about 3 seconds and goes off: the Fobik is learned.
  6. For each further Fobik start again from step 2.
Watch out: Needs two different working keys; with one key or none use a tool (it reads the PIN). The new Fobik must be blank: one already learned to another vehicle is refused. Up to eight keys. On a remote head key or Fobik the remote learns in the same procedure.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • Remote
    PIN read function

Without a tool

The remote is programmed on the car, without a tool. It takes two working keys.

When the key changed

Smart key (push to start)

  • 2011 - 2018Chip: ID46433 MHzFCC: M3N-40821302Hitag2 smart key; 4A fobs share the same FCC ID.
  • 2019 - 2023Chip: Hitag AES (4A)433 MHzFCC: M3N-40821302Same FCC ID as the ID46 fob: read the chip first.

Key with a blade (regular or flip)

  • 2005 - 2007Chip: ID46Blade: Y164FCC: KOBDT04ARemote head key (SKREEM).
  • 2008 - 2010This yearChip: ID46433 MHzFCC: IYZ-C01CFobik: the fob goes into the dash slot and turns, no blade.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chrysler 300 2008?

16 listings fit the Chrysler 300 2008: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 3-, 4-, 5- and 7-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chrysler 300 2008 remote use?

Listings for the Chrysler 300 2008 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Chrysler 300 2008 key use?

The listings for this car carry: ID46 (HITAG 2) · PCF7941 · NXP PCF7936AA. Check the chip in each listing's specifications.

Which FCC IDs do Chrysler 300 2008 remotes carry?

The remotes listed for this car carry FCC ID IYZC01C, K0BDT04A and M3N5WY783X. Match it with the FCC ID printed on your original remote.

Which tools program a Chrysler 300 2008 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Chrysler 300 2008 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes two working keys.