Skip to content

Ford F-450 2017 Key Fob & Car Keys

Keys that fit the 2017 Ford F-450: smart keys, flip keys and remote keys, 2, 3 or 4 buttons, FCC ID M3NA2C93142300, M3NA2C931426 or M3NA2C93142600, ID49 (HITAG Pro) or PCF7939FA chip, 315 MHz, 868 MHz or 902 MHz. 13 compatible keys, remotes & shells (genuine and aftermarket) available for the 2017 Ford F-450.

Last updated: 17 November 2026

Key specifications for the Ford F-450 2017

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz, 868 MHz and 902 MHz
Buttons
2-, 3-, 4- and 5-button
Transponder chip
ID49 (HITAG Pro) · PCF7939FA
Blade profile
HU101
Part numbers
HC3T-15K601-BA · 357141-00302 · 164-R8149 · PCF7939FA
Battery
CR2450 · CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz, 868 MHz and 902 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford F-450 2017 key

Smart key (push to start)

Programming steps

Add key - on the car(US / Canada cars)

Needs: Smart key (intelligent access, push button start) cars, two working programmed intelligent access keys inside the car, the new intelligent access key at hand

  1. With the car off, close every door and keep them closed. Finish all steps within 30 seconds from the start.
  2. Remove the tray and the cover from the center console. With the buttons facing up, place the first working key in the backup slot and press the START button.
  3. Wait 5 seconds, press the START button again, then take the key out.
  4. Within 10 seconds, place the second working key in the backup slot and press the START button.
  5. Wait 5 seconds, press the START button again, then take the key out.
  6. Wait 5 seconds, then place the new key in the backup slot and press the START button. Programming is done.
  7. Check that the new key's remote buttons work and that it starts the car.
  8. Not learned: wait 10 seconds and run the procedure again from step 1.
Watch out: All steps must be done within 30 seconds, with every door closed the whole time. A step done out of order: stop and wait at least 1 minute before starting again. Two working programmed intelligent access keys are needed. Up to 6 intelligent access keys can be programmed.

Key with a blade (regular or flip)

Programming steps

Add key - on the car(US / Canada cars)

Needs: Flip key or remote head key cars (SecuriLock), two working programmed SecuriLock keys, the new SecuriLock key, already cut

  1. Put the first working key in the ignition and switch from OFF to ON. Hold ON for 1 to 10 seconds.
  2. Switch back to OFF and pull the first key out.
  3. Wait at least 3 seconds but no more than 10, then put the second working key in and switch from OFF to ON. Hold ON for 1 to 10 seconds.
  4. Switch back to OFF and pull the second key out.
  5. Wait at least 3 seconds but no more than 10, then put the new key in and switch from OFF to ON. Hold ON for 1 to 10 seconds. The new key is now learned.
  6. For each extra new key, run steps 1 to 5 again from the start.
  7. Check the result: the new key starts the engine and its remote buttons work.
Watch out: The car holds 8 keys at most, and only SecuriLock keys work. Every ON hold is 1 to 10 seconds and every gap between keys is 3 to 10 seconds; outside these windows the car does not enter learn mode. Two working programmed keys are needed; with fewer, this method cannot be used.

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • from 2017This yearChip: ID49FCC: M3N-A2C93142300(US / Canada cars)Push-to-start trims; several fob frequencies exist.

Key with a blade (regular or flip)

  • 2011 - 2016Chip: 4D-63Blade: H75FCC: CWTWB1U793(US / Canada cars)80-bit version; some trucks have no chip in the key.
  • 2017 - 2022This yearChip: ID49Blade: HU101FCC: N5F-A08TAA, N5F-A08TDA(US / Canada cars)Flip key; 315 MHz and 902 MHz versions: read the FCC id.
  • from 2023Chip: ID49434 MHzBlade: HU198FCC: N5F-A08TBLP(US / Canada cars)Flip key, 434 MHz.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford F-450 2017?

13 listings fit the Ford F-450 2017: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Ford F-450 2017 remote use?

Listings for the Ford F-450 2017 come in 315 MHz, 868 MHz and 902 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Ford F-450 2017 key use?

The listings for this car carry: ID49 (HITAG Pro) · PCF7939FA. Check the chip in each listing's specifications.

Which FCC IDs do Ford F-450 2017 remotes carry?

The remotes listed for this car carry FCC ID M3NA2C93142300, M3NA2C931426 and M3NA2C93142600. Match it with the FCC ID printed on your original remote.

Which blade profile does the Ford F-450 2017 key use?

The blades listed for this car: HU101.

Can the Ford F-450 2017 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.