Skip to content

Ford F-550 2019 Key Fob & Car Keys

Keys that fit the 2018–2020 Ford F-550: smart keys, flip keys and remote keys, 2, 3 or 4 buttons, FCC ID M3NA2C93142300, M3NA2C931426 or M3NA2C93142600, ID49 (HITAG Pro) or PCF7939FA chip, 315 MHz, 868 MHz or 902 MHz. 17 compatible keys, remotes & shells (genuine and aftermarket) available for the 2019 Ford F-550.

Last updated: 17 November 2026

Key specifications for the Ford F-550 2018–2020

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz, 868 MHz and 902 MHz
Buttons
2-, 3-, 4- and 5-button
Transponder chip
ID49 (HITAG Pro) · PCF7939FA
Blade profile
HU101
Part numbers
164-R8130 · FL3T-15K601-CH · HC3T-15K601-BA · 357141-00302 · 164-R8149 · PCF7939FA
Battery
CR2032 · CR2450

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz, 868 MHz and 902 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford F-550 2019 key

Smart key (push to start)

Programming steps

Add key - on the car(US / Canada cars)

Needs: Smart key (intelligent access, push button start) cars, two working programmed intelligent access keys inside the car, the new intelligent access key at hand

  1. With the car off, close every door and keep them closed. Finish all steps within 30 seconds from the start.
  2. Slide the key blade out of each transmitter. Lift out the center console tray and cover to reach the backup slot.
  3. Place the first working key in the backup slot, buttons up, and press the START button.
  4. Wait 5 seconds, press the START button again, then take the key out.
  5. Within 10 seconds, place the second working key in the backup slot and press the START button.
  6. Wait 5 seconds, press the START button again, then take the key out.
  7. Wait 5 seconds, place the new key in the backup slot and press the START button. Programming is done.
  8. Check that the new key's remote buttons work and that it starts the car.
  9. Not learned: wait 10 seconds and run the procedure again from step 1.
Watch out: All steps must be done within 30 seconds, with every door closed the whole time. A step done out of order: stop and wait at least 1 minute before starting again. Two working programmed intelligent access keys are needed.

Key with a blade (regular or flip)

Programming steps

Add key - on the car(US / Canada cars)

Needs: Flip key cars, two working programmed keys, the new key, already cut

  1. Put the first working key in and turn it from OFF to RUN (not START) eight times, about as fast as you can.
  2. Switch quickly to the second working key and turn it from OFF to RUN (not START) two times, about as fast as you can. The dash shows the SecuriCode keypad door code.
  3. Switch quickly to the new key and turn it from OFF to RUN (not START). The dash shows Key Programmed; the hazard lights may flash and the locks may cycle.
  4. Turn the key OFF, pull it out and test the new key.
Watch out: Two working programmed keys are needed to add a third key. Entering program mode depends on the turning speed: too slow or too fast both fail, so several attempts may be needed.

Without a tool

The remote is programmed on the car, without a tool.

When the key changed

Smart key (push to start)

  • from 2017This yearChip: ID49FCC: M3N-A2C93142300(US / Canada cars)Push-to-start trims; several fob frequencies exist.

Key with a blade (regular or flip)

  • 2011 - 2016Chip: 4D-63Blade: H75FCC: CWTWB1U793(US / Canada cars)80-bit version; some trucks have no chip in the key.
  • 2017 - 2022This yearChip: ID49Blade: HU101FCC: N5F-A08TAA, N5F-A08TDA(US / Canada cars)Flip key; 315 MHz and 902 MHz versions: read the FCC id.
  • from 2023Chip: ID49434 MHzBlade: HU198FCC: N5F-A08TBLP(US / Canada cars)Flip key, 434 MHz.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford F-550 2018–2020?

17 listings fit the Ford F-550 2018–2020: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Ford F-550 2018–2020 remote use?

Listings for the Ford F-550 2018–2020 come in 315 MHz, 868 MHz and 902 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Ford F-550 2018–2020 key use?

The listings for this car carry: ID49 (HITAG Pro) · PCF7939FA. Check the chip in each listing's specifications.

Which FCC IDs do Ford F-550 2018–2020 remotes carry?

The remotes listed for this car carry FCC ID M3NA2C93142300, M3NA2C931426, M3NA2C93142600, N5FA08TAA and N5FA08TDA. Match it with the FCC ID printed on your original remote.

Which blade profile does the Ford F-550 2018–2020 key use?

The blades listed for this car: HU101.

Can the Ford F-550 2018–2020 remote be programmed without a tool?

The remote is programmed on the car, without a tool.