GMC Savana 2009 Key Fob & Car Keys
Keys that fit the 2008–2012 GMC Savana: smart keys, remote keys and transponder keys, 3 buttons, FCC ID 0UC60221 or 0UC60270, ID46 (HITAG 2) or NXP PCF7936AA chip, 315 MHz. 6 compatible keys, remotes & shells (genuine and aftermarket) available for the 2009 GMC Savana.
Last updated: 15 November 2026
Key specifications for the GMC Savana 2008–2012
- Key types
- smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
- Frequency
- 315 MHz
- Buttons
- 3-button
- Transponder chip
- ID46 (HITAG 2) · NXP PCF7936AA
- Battery
- CR2032
To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the GMC parts catalogue, with the specifications on each listing. Every remote listed for the GMC Savana 2008–2012 transmits on 315 MHz.
A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.
- $14.04In Stock
- $1.40In Stock
- $7.02In Stock
- $1.40In Stock
Programming the GMC Savana 2009 key
Key with a blade (regular or flip)
4 tools list this key. 3 of them list all keys lost.
- OBDSTAR Key Master G3
- Add key
- All keys lost
- Remote
reads the PIN by OBD - XTOOL X100 PAD3 / X100 MAX
- Add key
- All keys lost
- All keys lost
- Remote
- Launch X-431 IMMO
- Add key
All keys lost is listed by OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX and Lonsdor K518. Launch X-431 IMMO lists add key only.
Programming steps
Add key - on the car(US / Canada cars)
Needs: one working key, new key cut to the vehicle
- Cut the new key to the vehicle; have one key that already starts it.
- Start the engine with the working key, then turn it to LOCK/OFF and remove it.
- Within 10 seconds insert the new key and turn it to ON/RUN.
- The security light goes off when the key is learned (this can be too fast to notice).
- Start the engine with the new key; for each further key repeat from step 2.
All keys lost - on the car(US / Canada cars)
Needs: new key cut to the vehicle, 30 minutes
- Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
- Insert the new key and turn to ON/RUN without cranking; the security light comes on.
- Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
- Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
- After the third cycle turn to ON/RUN: this key is learned and every previously known key is erased.
- Learn the remaining keys with the add-key procedure.
Without a tool
The remote is programmed on the car, without a tool. Up to 8 remotes.
Programming steps
Program the remote without a tool(US / Canada cars)
Needs: Cars with Driver Information Center buttons, every remote to be programmed, the ignition key
- Insert the key and turn it to ON so the DIC is active.
- Step through the vehicle information menu until the cluster reads PRESS TO RELEARN REMOTE KEY.
- Press the SET/RESET button until REMOTE KEY LEARNING ACTIVE shows.
- Hold LOCK and UNLOCK together on the first remote for about 15 seconds. A chime confirms it is programmed.
- For each other remote, repeat steps 3 and 4.
- Turn the key OFF and take it out to exit, then test every remote.
Program the remote without a tool(US / Canada cars)
Needs: Cars without Driver Information Center buttons, every remote to be programmed, the ignition key
- Put the car in Park (P) and turn the key to ON, as far as it goes without cranking the engine.
- Push the trip reset stem repeatedly until the cluster reads RELEARN REMOTE KEY.
- Hold the trip odometer reset stem for three seconds. REMOTE KEY LEARNING ACTIVE shows.
- Hold LOCK and UNLOCK together on the first remote for about 15 seconds. A chime confirms it is programmed.
- For each other remote, repeat step 4.
- Turn the key OFF and take it out to exit, then test every remote.
When the key changed
Key with a blade (regular or flip)
- 1998 - 2007Chip: None (PassLock)(US / Canada cars)No chip in the key; PassLock sensor sits in the ignition lock.
- 2008 - 2023This yearChip: ID46(US / Canada cars)Circle Plus key; separate remote. Read the old key's blade.
Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.
Frequently asked questions
Which keys fit the GMC Savana 2008–2012?
6 listings fit the GMC Savana 2008–2012: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.
What frequency does the GMC Savana 2008–2012 remote use?
Every remote listed for the GMC Savana 2008–2012 transmits on 315 MHz.
Which transponder chip does the GMC Savana 2008–2012 key use?
The listings for this car carry: ID46 (HITAG 2) · NXP PCF7936AA. Check the chip in each listing's specifications.
Which FCC IDs do GMC Savana 2008–2012 remotes carry?
The remotes listed for this car carry FCC ID 0UC60221 and 0UC60270. Match it with the FCC ID printed on your original remote.
Which tools program a GMC Savana 2008–2012 key?
The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Lonsdor K518 and Launch X-431 IMMO for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.
Can the GMC Savana 2008–2012 remote be programmed without a tool?
The remote is programmed on the car, without a tool. Up to 8 remotes.





