Skip to content

Hummer H2 2008–2009 Key Fob & Car Keys

Keys that fit the 2008–2009 Hummer H2: smart keys, remote keys and transponder keys, 3 buttons, FCC ID 0UC60221 or 0UC60270, ID46 (HITAG 2) or NXP PCF7936AA chip, 315 MHz. 4 compatible keys, remotes & shells (genuine and aftermarket) available for the 2008 Hummer H2.

Last updated: 15 November 2026

Key specifications for the Hummer H2 2008–2009

Key types
smart keys, remote keys, transponder keys, key shells and key blanks
Frequency
315 MHz
Buttons
3-button
Transponder chip
ID46 (HITAG 2) · NXP PCF7936AA
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Hummer parts catalogue, with the specifications on each listing. Every remote listed for the Hummer H2 2008–2009 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Hummer H2 2008 key

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working key, new key cut to the vehicle

  1. Cut the new key to the vehicle; have one key that already starts it.
  2. Put the working key in the ignition and turn it to ON/RUN (or start the engine), then turn it to LOCK/OFF and remove it.
  3. Within five seconds insert the new key and turn it to ON/RUN.
  4. The security light goes off when the key is learned (this can be too fast to notice).
  5. Start the engine with the new key; for each further key repeat from step 2.
Watch out: Adds only; never erases keys. Up to 10 keys (owner's manual and service manual).
All keys lost - on the car(US / Canada cars)

Needs: new key cut to the vehicle, 30 minutes

  1. Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn to ON/RUN: this key is learned and every previously known key is erased.
  6. Learn the remaining keys with the add-key procedure.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer.

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Cars with Driver Information Center buttons, every remote to be programmed, the ignition key

  1. Insert the key and turn it to ON so the DIC is active.
  2. Step through the vehicle information menu until the cluster reads PRESS TO RELEARN REMOTE KEY.
  3. Press the SET/RESET button until REMOTE KEY LEARNING ACTIVE shows.
  4. Hold LOCK and UNLOCK together on the remote for about 15 seconds. A chime confirms it is programmed.
  5. For each other remote, repeat step 4.
  6. Turn the key OFF and take it out to exit, then test every remote.
Watch out: A maximum of eight remotes can be programmed.
Program the remote without a tool(US / Canada cars)

Needs: Cars without Driver Information Center buttons, every remote to be programmed, the ignition key

  1. Put the car in Park (P) and turn the key to ON, as far as it goes without cranking the engine.
  2. Push the trip reset stem repeatedly until the cluster reads RELEARN REMOTE KEY.
  3. Hold the trip odometer reset stem for three seconds. REMOTE KEY LEARNING ACTIVE shows.
  4. Hold LOCK and UNLOCK together on the first remote for about 15 seconds. A chime confirms it is programmed.
  5. For each other remote, repeat step 4.
  6. Turn the key OFF and take it out to exit, then test every remote.
Watch out: A maximum of eight remotes can be programmed.

When the key changed

Key with a blade (regular or flip)

  • 2003 - 2007Chip: None (PassLock)(US / Canada cars)No chip in the key; PassLock sensor sits in the ignition lock.
  • 2008 - 2009This yearChip: ID46Blade: B111(US / Canada cars)Circle Plus key; separate remote.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Hummer H2 2008–2009?

4 listings fit the Hummer H2 2008–2009: smart keys, remote keys, transponder keys, key shells and key blanks, in 3-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Hummer H2 2008–2009 remote use?

Every remote listed for the Hummer H2 2008–2009 transmits on 315 MHz.

Which transponder chip does the Hummer H2 2008–2009 key use?

The listings for this car carry: ID46 (HITAG 2) · NXP PCF7936AA. Check the chip in each listing's specifications.

Which FCC IDs do Hummer H2 2008–2009 remotes carry?

The remotes listed for this car carry FCC ID 0UC60221 and 0UC60270. Match it with the FCC ID printed on your original remote.

Which tools program a Hummer H2 2008–2009 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Hummer H2 2008–2009 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.