Skip to content

Hyundai Genesis 2012 Key Fob & Car Keys

Keys that fit the 2012 Hyundai Genesis: smart keys and transponder keys, 3 or 4 buttons, FCC ID SY5HMFNA04, SVICMFEU03 or SVIHMFCH34, NXP PCF7936AA or ID46 (HITAG 2) chip, 315 MHz or 433 MHz. 15 compatible keys, remotes & shells (genuine and aftermarket) available for the 2012 Hyundai Genesis.

Last updated: 16 November 2026

Key specifications for the Hyundai Genesis 2012

Key types
smart keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
3- and 4-button
Transponder chip
NXP PCF7936AA · ID46 (HITAG 2)
Blade profile
HYN14R · TOY48 · LXP90 · KK10
Part numbers
81996-2M020 · 81996-2M026 · 81996-2J700 · 81996-3S020 · 95440-3M110
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Hyundai parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Hyundai Genesis 2012 key

Smart key (push to start)

8 tools list this key. 3 of them list all keys lost.

All keys lost is listed by OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II and XTOOL X100 PAD3 / X100 MAX. Advanced Diagnostics Smart Pro, Launch X-431 IMMO, Lonsdor K518 and OBDSTAR X300 DP Plus list add key only.

Programming steps

Add key - Autel MaxiIM IM608

Needs: every fob the customer keeps (all are erased and learned again), new, never-learned smart key with the right chip and frequency, 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer

  1. Connect the IM608 by OBD, identify the car (VIN, or model and year) and open the Smart key system.
  2. Get the PIN: the tool's PIN function for the key type, or by VIN from the dealer.
  3. Start Smart key learning and accept the warning that all fobs will be erased.
  4. Ignition OFF, then enter the PIN when the tool asks.
  5. Press OK, then within 5 seconds press the start button with the first fob until the tool confirms (cars with a fob slot or holder: put the fob in it).
  6. Repeat for every fob, the old ones included; stop after the last one.
  7. Check that each fob locks, unlocks and starts the car.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
Add key - Lonsdor K518 (or OBDSTAR X300 DP, same route)

Needs: a working 46-chip smart key, MINI900 / ND900 (CN900 mini) decoder, every fob the customer keeps, new 46-chip smart key

  1. Take the battery out of the working fob.
  2. Collect the 12-digit key code with the MINI900 / ND900 held with the fob at the start button (fob-slot cars: remove the slot holder first; repeat if it fails).
  3. On the tool select the car, Read PinCode, then the 46 smart card PIN function, and enter the 12 digits as the tool asks.
  4. Note the 6-digit PIN the tool returns.
  5. Run Smart key programming: ignition OFF, enter the PIN, then press the start button with each fob within 5 seconds (or put it in the slot) until each is accepted.
  6. Learn every fob to keep, then test lock, unlock and start.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
All keys lost - Autel MaxiIM IM608

Needs: two new, never-learned smart keys with the right chip and frequency, PIN by VIN from the dealer, emergency blade cut to the door lock

  1. Open the car with the emergency blade cut to the door lock.
  2. Connect the IM608 by OBD and enter the VIN by hand (auto VIN can fail with no fob in the car).
  3. Get the PIN by VIN from the dealer.
  4. Start Smart key learning and accept the erase warning.
  5. Ignition OFF, then enter the PIN when the tool asks.
  6. Press OK, then within 5 seconds press the start button with the first new fob until the tool confirms.
  7. Repeat for the second fob, then test lock, unlock and start with each.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Lost fobs are erased by the learning. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).

Key with a blade (regular or flip)

5 tools list this key. 4 of them list all keys lost.

    • Add key
    • All keys lost
    • Remote
    PIN read function
  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    PIN read function
    • Add key(US / Canada cars)
    • All keys lost(US / Canada cars)
  • Lonsdor KH100
    • Remote

Programming steps

Add key - Autel MaxiIM IM608 (Transmitter code saving)(US / Canada cars)

Needs: working key to copy, remote (flip key or separate fob) for the car, every remote the customer keeps

  1. Confirm the car has no immobilizer: turn-key ignition, no start button and no immobilizer lamp in the cluster (the dealer can confirm by VIN).
  2. Duplicate the working key; with no immobilizer it starts the engine without programming.
  3. Connect the tool by OBD and open Transmitter code saving (remote keyless entry).
  4. Ignition OFF and key out when asked, then press LOCK on the first remote about 2 seconds after confirming.
  5. Repeat for each remote to keep (up to 4), then test lock and unlock.
  6. If the car has the dealer anti-theft logic upgrade, check it starts after locking and unlocking with the new remote.
Watch out: Only for US cars built without an immobilizer; a car with the immobilizer lamp follows the blade key teaching case. With the dealer anti-theft logic installed, locking with the fob arms the start block and unlocking with a learned fob releases it: the customer needs a learned remote. Remote code saving can drop remotes not pressed in the session: bring them all.
Add key - Lonsdor K518 (46-chip PIN read by OBD)

Needs: new 46-chip key(s) cut to the lock, every key the customer keeps

  1. Connect the K518 by OBD.
  2. Read PIN code (46 chip) by OBD with the ignition ON (a cut, unprogrammed key turns the lock).
  3. Open the Immobilizer key programming menu for the car, switch ON with the first key and enter the PIN.
  4. Program the first key, then switch off, insert the next key, switch ON and program it; repeat for every key to keep.
  5. Leave the ignition off for about 10 seconds and start with each key.
  6. Program the remotes in the Remote control system menu (ignition ON then OFF, key out, press a button on each remote when asked; up to 4).
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.
All keys lost - Autel MaxiIM IM608 (Transmitter code saving)(US / Canada cars)

Needs: key code or lock decoding, remote (flip key or separate fob) for the car, every remote the customer keeps

  1. Confirm the car has no immobilizer: turn-key ignition, no start button and no immobilizer lamp in the cluster (the dealer can confirm by VIN).
  2. Cut the new key by key code or by decoding the lock; with no immobilizer it starts the engine without programming.
  3. Connect the tool by OBD and open Transmitter code saving (remote keyless entry).
  4. Ignition OFF and key out when asked, then press LOCK on the first remote about 2 seconds after confirming.
  5. Repeat for each remote to keep (up to 4), then test lock and unlock.
  6. If the car has the dealer anti-theft logic upgrade, check it starts after locking and unlocking with the new remote.
Watch out: Only for US cars built without an immobilizer; a car with the immobilizer lamp follows the blade key teaching case. With the dealer anti-theft logic installed, locking with the fob arms the start block and unlocking with a learned fob releases it: the customer needs a learned remote. Remote code saving can drop remotes not pressed in the session: bring them all.
All keys lost - Lonsdor K518 (46-chip PIN read by OBD)

Needs: new 46-chip key(s) cut to the lock, at least two new keys

  1. Connect the K518 by OBD.
  2. Read PIN code (46 chip) by OBD with the ignition ON (a cut, unprogrammed key turns the lock).
  3. Open the Immobilizer key programming menu for the car, switch ON with the first key and enter the PIN.
  4. Program the first key, then switch off, insert the next key, switch ON and program it; repeat for every key to keep.
  5. Leave the ignition off for about 10 seconds and start with each key.
  6. Program the remotes in the Remote control system menu (ignition ON then OFF, key out, press a button on each remote when asked; up to 4).
Watch out: Lost keys stop starting the car once the new set is taught. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.

When the key changed

Smart key (push to start)

  • 2009 - 2014This yearChip: ID46FCC: SY5HMFNA04Sedan (BH): US fobs 315 MHz, GCC fobs 433 MHz
  • 2010 - 2016This yearChip: ID46FCC: SY5HMFNA04, SY5RBFNA433Coupe (BK): 315 MHz fobs to 2013, 433 MHz 95440-2M420 from 2013
  • 2015 - 2016Chip: ID47433 MHzFCC: SY5DHFNA433Sedan (DH); sold as Genesis G80 from 2017 (G80 lines)
  • 2017 - 2022Chip: ID47433 MHzFCC: SY5HIFGE04Genesis G90 (HI); EQ900 in Korea from 2016
  • from 2022Chip: ID47433 MHzFCC: TQ8-FOB-4F53UGenesis G90 (RS4); US from the 2023 model year

Key with a blade (regular or flip)

  • 2009 - 2014This yearChip: ID46Sedan (BH) without push start
  • 2010 - 2013This yearChip: ID46(US / Canada cars)Coupe (BK) turn-key; some US 2011-2014 coupes have no immobilizer

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Hyundai Genesis 2012?

15 listings fit the Hyundai Genesis 2012: smart keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Hyundai Genesis 2012 remote use?

Listings for the Hyundai Genesis 2012 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Hyundai Genesis 2012 key use?

The listings for this car carry: NXP PCF7936AA · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Hyundai Genesis 2012 remotes carry?

The remotes listed for this car carry FCC ID SVICMFEU03, SVIHMFCH34, SVIHMFEU04, SVIHMFKR04, SY5HMFNA04 and SY5RBFNA433. Match it with the FCC ID printed on your original remote.

Which blade profile does the Hyundai Genesis 2012 key use?

The blades listed for this car: HYN14R · TOY48 · LXP90 · KK10.

Which tools program a Hyundai Genesis 2012 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II, XTOOL X100 PAD3 / X100 MAX, Advanced Diagnostics Smart Pro, Launch X-431 IMMO and Lonsdor K518 for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.