Skip to content

Hyundai Veracruz 2007–2008 Key Fob & Car Keys

Keys that fit the 2007–2008 Hyundai Veracruz: smart keys, flip keys and remote keys, 4 buttons, FCC ID SY5VISMKFNA04 or SY5AVISMKFNA04, ID46 (HITAG 2) or NXP PCF7936AA chip, 315 MHz or 447 MHz. 12 compatible keys, remotes & shells (genuine and aftermarket) available for the 2007 Hyundai Veracruz.

Last updated: 15 November 2026

Key specifications for the Hyundai Veracruz 2007–2008

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 447 MHz
Buttons
4-button
Transponder chip
ID46 (HITAG 2) · NXP PCF7936AA · CN3 cloning chip
Blade profile
HYN14R
Part numbers
95430-3J100 · 81996-2B020 · 81996-3J000 · 95440-3J600
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Hyundai parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 447 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Hyundai Veracruz 2007 key

Smart key (push to start)

6 tools list this key. 4 of them list all keys lost.

All keys lost is listed by OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II, Lonsdor K518 and XTOOL X100 PAD3 / X100 MAX. Launch X-431 IMMO lists add key only.

Programming steps

Add key - Autel MaxiIM IM608

Needs: every fob the customer keeps (all are erased and learned again), new, never-learned smart key with the right chip and frequency, 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer

  1. Connect the IM608 by OBD, identify the car (VIN, or model and year) and open the Smart key system.
  2. Get the PIN: the tool's PIN function for the key type, or by VIN from the dealer.
  3. Start Smart key learning and accept the warning that all fobs will be erased.
  4. Ignition OFF, then enter the PIN when the tool asks.
  5. Press OK, then within 5 seconds press the start button with the first fob until the tool confirms (cars with a fob slot or holder: put the fob in it).
  6. Repeat for every fob, the old ones included; stop after the last one.
  7. Check that each fob locks, unlocks and starts the car.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
Add key - Lonsdor K518

Needs: every fob the customer keeps (all are erased and learned again), new, never-learned smart key with the right chip and frequency, 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer

  1. Connect the K518 by OBD, identify the car (VIN, or model and year) and open the Smart key system.
  2. Get the PIN: the tool's PIN function for the key type, or by VIN from the dealer.
  3. Start Smart key learning and accept the warning that all fobs will be erased.
  4. Ignition OFF, then enter the PIN when the tool asks.
  5. Press OK, then within 5 seconds press the start button with the first fob until the tool confirms (cars with a fob slot or holder: put the fob in it).
  6. Repeat for every fob, the old ones included; stop after the last one.
  7. Check that each fob locks, unlocks and starts the car.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
All keys lost - Autel MaxiIM IM608

Needs: two new, never-learned smart keys with the right chip and frequency, PIN by VIN from the dealer, emergency blade cut to the door lock

  1. Open the car with the emergency blade cut to the door lock.
  2. Connect the IM608 by OBD and enter the VIN by hand (auto VIN can fail with no fob in the car).
  3. Get the PIN by VIN from the dealer.
  4. Start Smart key learning and accept the erase warning.
  5. Ignition OFF, then enter the PIN when the tool asks.
  6. Press OK, then within 5 seconds press the start button with the first new fob until the tool confirms.
  7. Repeat for the second fob, then test lock, unlock and start with each.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Lost fobs are erased by the learning. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
All keys lost - Lonsdor K518

Needs: two new, never-learned smart keys with the right chip and frequency, PIN by VIN from the dealer, emergency blade cut to the door lock

  1. Open the car with the emergency blade cut to the door lock.
  2. Connect the K518 by OBD and enter the VIN by hand (auto VIN can fail with no fob in the car).
  3. Get the PIN by VIN from the dealer.
  4. Start Smart key learning and accept the erase warning.
  5. Ignition OFF, then enter the PIN when the tool asks.
  6. Press OK, then within 5 seconds press the start button with the first new fob until the tool confirms.
  7. Repeat for the second fob, then test lock, unlock and start with each.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Lost fobs are erased by the learning. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).

Key with a blade (regular or flip)

4 tools list this key. 3 of them list all keys lost.

    • Add key
    • All keys lost
    • Remote
    PIN read function
  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    PIN read function
    • Remote

Programming steps

Add key - Lonsdor K518 (46-chip PIN read by OBD)

Needs: new 46-chip key(s) cut to the lock, every key the customer keeps

  1. Connect the K518 by OBD.
  2. Read PIN code (46 chip) by OBD with the ignition ON (a cut, unprogrammed key turns the lock).
  3. Open the Immobilizer key programming menu for the car, switch ON with the first key and enter the PIN.
  4. Program the first key, then switch off, insert the next key, switch ON and program it; repeat for every key to keep.
  5. Leave the ignition off for about 10 seconds and start with each key.
  6. Program the remotes in the Remote control system menu (ignition ON then OFF, key out, press a button on each remote when asked; up to 4).
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.
All keys lost - Lonsdor K518 (46-chip PIN read by OBD)

Needs: new 46-chip key(s) cut to the lock, at least two new keys

  1. Connect the K518 by OBD.
  2. Read PIN code (46 chip) by OBD with the ignition ON (a cut, unprogrammed key turns the lock).
  3. Open the Immobilizer key programming menu for the car, switch ON with the first key and enter the PIN.
  4. Program the first key, then switch off, insert the next key, switch ON and program it; repeat for every key to keep.
  5. Leave the ignition off for about 10 seconds and start with each key.
  6. Program the remotes in the Remote control system menu (ignition ON then OFF, key out, press a button on each remote when asked; up to 4).
Watch out: Lost keys stop starting the car once the new set is taught. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.

When the key changed

Smart key (push to start)

  • 2007 - 2012This yearChip: ID46433 MHz(GCC / Europe cars)Sold as ix55 in Europe; smart keys 95440-3J500 / 3J501
  • 2007 - 2012This yearChip: ID46315 MHzFCC: SY5SVISMKFNA04(US / Canada cars)EN; learning steps need the PIN, max 2 fobs

Key with a blade (regular or flip)

  • 2007 - 2012This yearChip: ID46Transponder key with a separate remote (95430-3J500)

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Hyundai Veracruz 2007–2008?

12 listings fit the Hyundai Veracruz 2007–2008: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Hyundai Veracruz 2007–2008 remote use?

Listings for the Hyundai Veracruz 2007–2008 come in 315 MHz and 447 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Hyundai Veracruz 2007–2008 key use?

The listings for this car carry: ID46 (HITAG 2) · NXP PCF7936AA · CN3 cloning chip. Check the chip in each listing's specifications.

Which FCC IDs do Hyundai Veracruz 2007–2008 remotes carry?

The remotes listed for this car carry FCC ID SY5AVISMKFNA04 and SY5VISMKFNA04. Match it with the FCC ID printed on your original remote.

Which blade profile does the Hyundai Veracruz 2007–2008 key use?

The blades listed for this car: HYN14R.

Which tools program a Hyundai Veracruz 2007–2008 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II, Lonsdor K518, XTOOL X100 PAD3 / X100 MAX, Launch X-431 IMMO and Autel KM100 (IKEY universal smart key) for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.