Skip to content

Jeep Commander 2009 Key Fob & Car Keys

Keys that fit the 2008–2010 Jeep Commander: remote keys and transponder keys, 2, 3 or 5 buttons, FCC ID IYZC01C or M3N5WY783X, PCF7941 or NXP PCF7936AA chip, 433 MHz. 10 compatible keys, remotes & shells (genuine and aftermarket) available for the 2009 Jeep Commander.

Last updated: 15 November 2026

Key specifications for the Jeep Commander 2008–2010

Key types
remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
433 MHz
Buttons
2-, 3-, 5-, 6- and 7-button
Transponder chip
PCF7941 · NXP PCF7936AA
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Jeep parts catalogue, with the specifications on each listing. Every remote listed for the Jeep Commander 2008–2010 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Jeep Commander 2009 key

Smart key (push to start)

One tool lists this key.

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    PIN read function

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working programmed keys, a new key cut to the car

  1. Insert the first working key and turn it to ON/RUN for at least 3 and no more than 15 seconds, then turn it to LOCK and remove it.
  2. Within 15 seconds, insert the second working key and turn it to ON/RUN. After 10 seconds a chime sounds and the Vehicle Security Light starts flashing. Turn it to LOCK and remove it.
  3. Within 60 seconds, insert the new key and turn it to ON/RUN. After 10 seconds one chime sounds and the Vehicle Security Light stops flashing.
  4. The security light comes on again for a few seconds and goes off: the new key is programmed, and its remote (RKE) is learned at the same time.
  5. Repeat the whole procedure for each extra key.
Watch out: Needs two working keys; with fewer, the key must be programmed with a tool. Up to eight keys can be programmed.
Add key - on the car(US / Canada cars)

Needs: two working Fobiks, new blank Fobik

  1. Have the new (never programmed) Fobik ready; have two different Fobiks that already start the vehicle.
  2. Insert the first working Fobik and turn to ON for at least 3 but no more than 15 seconds, then turn OFF and remove it.
  3. Within 15 seconds insert the second working Fobik and turn to ON; after about 10 seconds a chime sounds and the security light flashes. Turn OFF and remove it.
  4. Within 60 seconds (stay under 50 to be safe) insert the new blank Fobik and turn to ON.
  5. After about 10 seconds a single chime sounds, the light stops flashing, stays on about 3 seconds and goes off: the Fobik is learned.
  6. For each further Fobik start again from step 2.
Watch out: Needs two different working keys; with one key or none use a tool (it reads the PIN). The new Fobik must be blank: one already learned to another vehicle is refused. Up to eight keys. On a remote head key or Fobik the remote learns in the same procedure. The customer learn works only on US-market vehicles; a GCC or export car needs a tool.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Remote

Without a tool

The remote is programmed on the car, without a tool. It takes two working keys.

When the key changed

Key with a blade (regular or flip)

  • 2006 - 2007Chip: ID46Blade: Y164FCC: OHT692427AA, KOBDT04ARemote head key (SKREEM); US remote heads are 315 MHz.
  • 2008 - 2010This yearChip: ID46433 MHzFCC: IYZ-C01C, M3N5WY783XFobik: the fob goes into the dash slot and turns, no blade.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Jeep Commander 2008–2010?

10 listings fit the Jeep Commander 2008–2010: remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 3-, 5-, 6- and 7-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Jeep Commander 2008–2010 remote use?

Every remote listed for the Jeep Commander 2008–2010 transmits on 433 MHz.

Which transponder chip does the Jeep Commander 2008–2010 key use?

The listings for this car carry: PCF7941 · NXP PCF7936AA. Check the chip in each listing's specifications.

Which FCC IDs do Jeep Commander 2008–2010 remotes carry?

The remotes listed for this car carry FCC ID IYZC01C and M3N5WY783X. Match it with the FCC ID printed on your original remote.

Which tools program a Jeep Commander 2008–2010 key?

The tool makers' coverage lists name Lonsdor K518, OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Jeep Commander 2008–2010 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes two working keys.