Skip to content

Jeep Commander 2010 Key Fob & Car Keys

Keys that fit the 2008–2010 Jeep Commander: remote keys and transponder keys, 2, 3 or 5 buttons, FCC ID IYZC01C or M3N5WY783X, PCF7941 or NXP PCF7936AA chip, 433 MHz. 10 compatible keys, remotes & shells (genuine and aftermarket) available for the 2010 Jeep Commander.

Last updated: 15 November 2026

Key specifications for the Jeep Commander 2008–2010

Key types
remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
433 MHz
Buttons
2-, 3-, 5-, 6- and 7-button
Transponder chip
PCF7941 · NXP PCF7936AA
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Jeep parts catalogue, with the specifications on each listing. Every remote listed for the Jeep Commander 2008–2010 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Jeep Commander 2010 key

Smart key (push to start)

One tool lists this key.

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    PIN read function

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working programmed (or original) keys, a new key cut to the car

  1. Put the first working key in the ignition, turn to ON, wait about 3 seconds, then turn OFF and take it out.
  2. Within 15 seconds, put the second working key in, turn to ON and wait about 10 seconds. The immobilizer light comes on and a tone sounds. Turn OFF and take the key out.
  3. Within 50 seconds, put the new key in and turn to ON.
  4. After about 10 seconds a tone sounds and the immobilizer light stays on for 3 seconds: the new key is programmed.
  5. For each extra key, start again from step 1.
Watch out: 2010 and later cars need an automotive locksmith or the dealer; this method does not apply to them. If the ignition recall was carried out on the car, this method is not available. Some 2009 and later Dodge Ram trucks may need dealer programming.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Remote

Without a tool

The remote is not programmed on the car by hand: it needs a tool or a dealer.

When the key changed

Key with a blade (regular or flip)

  • 2006 - 2007Chip: ID46Blade: Y164FCC: OHT692427AA, KOBDT04ARemote head key (SKREEM); US remote heads are 315 MHz.
  • 2008 - 2010This yearChip: ID46433 MHzFCC: IYZ-C01C, M3N5WY783XFobik: the fob goes into the dash slot and turns, no blade.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Jeep Commander 2008–2010?

10 listings fit the Jeep Commander 2008–2010: remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 3-, 5-, 6- and 7-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Jeep Commander 2008–2010 remote use?

Every remote listed for the Jeep Commander 2008–2010 transmits on 433 MHz.

Which transponder chip does the Jeep Commander 2008–2010 key use?

The listings for this car carry: PCF7941 · NXP PCF7936AA. Check the chip in each listing's specifications.

Which FCC IDs do Jeep Commander 2008–2010 remotes carry?

The remotes listed for this car carry FCC ID IYZC01C and M3N5WY783X. Match it with the FCC ID printed on your original remote.

Which tools program a Jeep Commander 2008–2010 key?

The tool makers' coverage lists name Lonsdor K518, OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Jeep Commander 2008–2010 remote be programmed without a tool?

The remote is not programmed on the car by hand: it needs a tool or a dealer.