Skip to content

Kia Sportage 2016 Key Fob & Car Keys

Keys that fit the 2016 Kia Sportage: smart keys, flip keys and remote keys, 3 or 4 buttons, FCC ID TQ8RKE4F27, RKE4F26 or F0B4F08, 4D-60 (80-bit) or NXP PCF7936AA chip, 315 MHz or 433 MHz. 18 compatible keys, remotes & shells (genuine and aftermarket) available for the 2016 Kia Sportage.

Last updated: 12 November 2026

Key specifications for the Kia Sportage 2016

Key types
smart keys, flip keys, remote keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
3- and 4-button
Transponder chip
4D-60 (80-bit) · NXP PCF7936AA · ID47 (HITAG 3)
Blade profile
KIA7 · HY22 · KK10
Part numbers
95430-3W350 · 95440-D9000 · 95430-D9000 · 81996-A4040 · 95440-D9100 · 95430-D9100
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Kia parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Kia Sportage 2016 key

Smart key (push to start)

6 tools list this key. 3 of them list all keys lost.

All keys lost is listed by OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II and XTOOL X100 PAD3 / X100 MAX. Launch X-431 IMMO and Lonsdor K518 list add key only.

Programming steps

Add key - Autel MaxiIM IM608

Needs: every fob the customer keeps (all are erased and learned again), new, never-learned smart key with the right chip and frequency, 6-digit PIN: tool read (by OBD on 8A cars; with a working fob on 46 / 47 / 4A cars where Autel lists it) or by VIN from the dealer

  1. Connect the IM608 by OBD, identify the car by VIN and open the Smart key (SMK) system; check SMK status and the current fob first.
  2. Read the PIN with the tool's function for the key type, or get it by VIN from the dealer.
  3. Start Smart key learning and accept the warning that all fobs will be erased.
  4. Ignition OFF (cluster dark), open and close the driver's door, then enter the PIN.
  5. Press OK, then within 5 seconds press and hold the start button with the back / top of the first fob for about 5 seconds until the immobilizer lamp flashes (cars with a fob slot: put the fob in the slot).
  6. Repeat for every fob, the old ones included; cancel when the last one is done.
  7. Check that each fob locks, unlocks and starts the car; read the key count.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob). If a fob is not accepted, take the board out of the shell and press it to the start button again (both tool guides give this tip).
All keys lost - Autel MaxiIM IM608

Needs: two new, never-learned smart keys with the right chip and frequency, PIN by VIN from the dealer (no Autel all-keys-lost PIN read found for this car's chip), emergency blade cut to the door lock

  1. Open the car with the emergency blade cut to the door lock.
  2. Connect the IM608 by OBD and identify the car (enter the VIN by hand if auto VIN fails with no fob present).
  3. Get the PIN by VIN from the dealer.
  4. Start Smart key learning and accept the erase warning.
  5. Ignition OFF, open and close the driver's door, enter the PIN.
  6. Press OK, then within 5 seconds hold the back / top of the first new fob on the start button for about 5 seconds until the immobilizer lamp flashes.
  7. Repeat for the second fob, then test lock, unlock and start with each.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. If a fob is not accepted, take the board out of the shell and press it to the start button again (both tool guides give this tip). Lost fobs are erased by the learning.

Key with a blade (regular or flip)

4 tools list this key. 3 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
    • Add key
    • All keys lost
    • Add key
    • Remote
    PIN read function

All keys lost is listed by OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX and Autel IM608 II / IM608 Pro II. Lonsdor K518 lists add key only.

Programming steps

Add key - Autel MaxiIM IM608

Needs: every key the customer keeps (all are taught again), new transponder key or flip remote cut to the lock, 6-digit PIN: read by OBD on 46-chip SMARTRA cars, read from a working key on 80-bit (4D / DST80) cars where Autel lists it (XP400 + APB131), otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Check the cluster shows an immobilizer lamp at ignition ON (US turn-key cars without one: use the US no-immobilizer case).
  2. Connect the IM608 by OBD, identify the car by VIN and open the Immobilizer system.
  3. Read the PIN with the tool's PIN function for the chip type; if the car is not listed, get the PIN by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach the first key; when asked, switch off, insert the next key and switch ON within about 10 seconds. Repeat for every key, the working ones included.
  6. Finish, leave the ignition off for about 10 seconds, then start the engine with each key.
  7. Learn the remote buttons with Transmitter code saving (ignition off, key out, press LOCK on each remote when prompted).
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done. Up to 8 transponder keys and 4 remotes.
Add key - Autel MaxiIM IM608 (Transmitter code saving)(US / Canada cars)

Needs: working key to copy, remote (flip key or separate fob) for the car, every remote the customer keeps

  1. Confirm the car has no immobilizer: turn-key ignition, no start button and no immobilizer lamp in the cluster (the dealer can confirm by VIN).
  2. Duplicate the working key; with no immobilizer it starts the engine without programming.
  3. Connect the tool by OBD and open Transmitter code saving (remote keyless entry).
  4. Ignition OFF and key out when asked, then press LOCK on the first remote about 2 seconds after confirming.
  5. Repeat for each remote to keep (up to 4), then test lock and unlock.
  6. If the car has the dealer anti-theft logic upgrade, check it starts after locking and unlocking with the new remote.
Watch out: Only for US cars built without an immobilizer; a car with the immobilizer lamp follows the blade key teaching case. With the dealer anti-theft logic installed, locking with the fob arms the start block and unlocking with a learned fob releases it: the customer needs a learned remote. Remote code saving can drop remotes not pressed in the session: bring them all.
All keys lost - Autel MaxiIM IM608

Needs: two new transponder keys or flip remotes cut to the lock (by key code or decoding), 6-digit PIN: read by OBD on 46-chip SMARTRA cars; by VIN from the dealer on 80-bit (4D / DST80) cars, whose PIN read needs a working key, battery support (stable 12 V)

  1. Cut a new key to the door / ignition lock so the ignition can be switched ON.
  2. Connect the IM608 by OBD, identify the car by VIN and open the Immobilizer system.
  3. Get the PIN: tool PIN read by OBD on 46-chip SMARTRA cars, otherwise by VIN from the dealer.
  4. Start Key learning, switch ON with the first new key and enter the PIN.
  5. Teach each new key in turn (switch off, next key, ON within about 10 seconds).
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Lost keys stop starting the car once the new set is taught. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.
All keys lost - Autel MaxiIM IM608 (Transmitter code saving)(US / Canada cars)

Needs: key code or lock decoding, remote (flip key or separate fob) for the car, every remote the customer keeps

  1. Confirm the car has no immobilizer: turn-key ignition, no start button and no immobilizer lamp in the cluster (the dealer can confirm by VIN).
  2. Cut the new key by key code or by decoding the lock; with no immobilizer it starts the engine without programming.
  3. Connect the tool by OBD and open Transmitter code saving (remote keyless entry).
  4. Ignition OFF and key out when asked, then press LOCK on the first remote about 2 seconds after confirming.
  5. Repeat for each remote to keep (up to 4), then test lock and unlock.
  6. If the car has the dealer anti-theft logic upgrade, check it starts after locking and unlocking with the new remote.
Watch out: Only for US cars built without an immobilizer; a car with the immobilizer lamp follows the blade key teaching case. With the dealer anti-theft logic installed, locking with the fob arms the start block and unlocking with a learned fob releases it: the customer needs a learned remote. Remote code saving can drop remotes not pressed in the session: bring them all.

When the key changed

Smart key (push to start)

  • 2011 - 2015Chip: ID46FCC: SY5HMFNA04
  • 2016 - 2022This yearChip: ID47433 MHzFCC: TQ8-FOB-4F08, TQ8-FOB-4F24
  • from 2022Chip: 4A433 MHzFCC: SY5MQ4FGE05, SY5MQ4FGE07, SY5MQ4AFGE04US cars from 2023

Key with a blade (regular or flip)

  • 1999 - 2001Chip: ID48(GCC / Europe cars)
  • 2001 - 2003Chip: 4D-60(GCC / Europe cars)2001 cars can have either ID48 or 4D-60
  • 2004 - 2010Chip: ID46(GCC / Europe cars)
  • 2016 - 2019This yearChip: ID46FCC: TQ8-RKE-4F27(US / Canada cars)Transponder flip 95430-D9000 (TP); most US turn-key cars have no chip
  • 2016 - 2021This yearChip: DST80433 MHz(GCC / Europe cars)Flip key chip sold as 4D60 80-bit
  • from 2022Chip: 4A433 MHzUS flip 95430-R0100 has no chip

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Kia Sportage 2016?

18 listings fit the Kia Sportage 2016: smart keys, flip keys, remote keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Kia Sportage 2016 remote use?

Listings for the Kia Sportage 2016 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Kia Sportage 2016 key use?

The listings for this car carry: 4D-60 (80-bit) · NXP PCF7936AA · ID47 (HITAG 3). Check the chip in each listing's specifications.

Which FCC IDs do Kia Sportage 2016 remotes carry?

The remotes listed for this car carry FCC ID F0B4F08, NY0DD4TX1306TFL, RKE4F26, TQ8F0B4F08 and TQ8RKE4F27. Match it with the FCC ID printed on your original remote.

Which blade profile does the Kia Sportage 2016 key use?

The blades listed for this car: KIA7 · HY22 · KK10.

Which tools program a Kia Sportage 2016 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II, XTOOL X100 PAD3 / X100 MAX, Launch X-431 IMMO, Lonsdor K518 and Autel KM100 (IKEY universal smart key) for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.