Skip to content

Lincoln LS 2004 Key Fob & Car Keys

Keys that fit the 2003–2006 Lincoln LS: transponder keys, 4D-63 (80-bit) chip. 4 compatible keys, remotes & shells (genuine and aftermarket) available for the 2004 Lincoln LS.

Last updated: 3 November 2026

Key specifications for the Lincoln LS 2003–2006

Key types
transponder keys, key shells and emergency blades
Transponder chip
4D-63 (80-bit)
Blade profile
FO38

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Lincoln parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Lincoln LS 2004 key

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed

Programming steps

Add key - on the car(US / Canada cars)

Needs: two original Ford keys that start the car, a new key already cut to the car

  1. Put the first working key in the ignition, turn to ON (just before cranking) for at least one second, then back to OFF.
  2. Take it out. Within 10 seconds put the second working key in, turn to ON for at least one second and no more than 10 seconds, then OFF, and take it out.
  3. Within 20 seconds, put the new key in, turn to ON for at least one second, then back to OFF.
  4. The security light comes on for 3 seconds: the new key is programmed.
Watch out: With only one working key or none, a dealer or locksmith must program it. A cloned key from a hardware store does not count; both keys must be original programmed keys. Hardware stores cannot program these keys; only an automotive locksmith or the dealer can.
Add key - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  2. Read the key count first and note it.
  3. Put the new key in the ignition, switch ON and choose Add key.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool reports the key is programmed, leave the new key at ON for about 20 seconds, then switch OFF.
  6. Read the key count again, then start the engine with the new key and with an old key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys. With no working key left, use All keys lost instead: Add key does not erase the old keys.
All keys lost - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the car will not start with fewer than two learned keys.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost (erase keys and program).
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys; follow its prompts to switch OFF and back ON so the first key is learned.
  6. When asked, insert the second new key and switch ON for about 10 seconds.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Procedure A (the owner's manual names the right procedure; otherwise try A, then B), every remote the customer keeps

  1. Close all doors, open the driver's door, press UNLOCK on the driver's door switch while the door is open, and insert the key.
  2. Turn the ignition from OFF to RUN 8 times within 8 seconds, ending in RUN (RUN = just before cranking). The locks cycle: programming mode. If they do not, take the key out and start again.
  3. Within 10 seconds, press any button on the first remote. The locks cycle to confirm.
  4. Within 10 seconds, press any button on the next remote. The locks cycle again. Repeat for every remote.
  5. Turn the ignition to OFF. The locks cycle to close programming mode.
  6. If this fails, run the same procedure with the driver's door closed.
Watch out: This resets every remote of the car; reprogram all working remotes in the same session. Never press the brake pedal before or during the procedure. Work quickly. No chime or lock cycle at the start means the car never entered programming mode: take the key out, open and close the door, and start again.
Program the remote without a tool(US / Canada cars)

Needs: Procedure B (a chime confirms each stage), every remote the customer keeps

  1. Fasten the seat belt and close all doors.
  2. Turn the ignition from OFF to RUN 4 times within 3 seconds.
  3. Turn the ignition to OFF. A chime confirms programming mode.
  4. Within 10 seconds, press and hold any button on the first remote. One chime confirms it.
  5. Within 10 seconds, press and hold any button on the second remote. One chime confirms it.
  6. Turn the ignition to RUN to leave programming mode.
Watch out: This resets every remote of the car; reprogram all working remotes in the same session. Never press the brake pedal before or during the procedure. Work quickly. No chime or lock cycle at the start means the car never entered programming mode: take the key out, open and close the door, and start again.

When the key changed

Key with a blade (regular or flip)

  • 2000 - 2002Chip: 4D-60Blade: H75(US / Canada cars)Large glass 4D-60 chip; separate remote.
  • 2003 - 2006This yearChip: 4D-63Blade: H75(US / Canada cars)40-bit version; an 80-bit key also programs.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Lincoln LS 2003–2006?

4 listings fit the Lincoln LS 2003–2006: transponder keys, key shells and emergency blades. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which transponder chip does the Lincoln LS 2003–2006 key use?

The listings for this car carry: 4D-63 (80-bit). Check the chip in each listing's specifications.

Which blade profile does the Lincoln LS 2003–2006 key use?

The blades listed for this car: FO38.

Which tools program a Lincoln LS 2003–2006 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Lincoln LS 2003–2006 remote be programmed without a tool?

The remote is programmed on the car, without a tool.