Skip to content

Suzuki SX4 2008–2011 Key Fob & Car Keys

Keys that fit the 2008–2011 Suzuki SX4: smart keys and transponder keys, 2 buttons, FCC ID TS001. 3 compatible keys, remotes & shells (genuine and aftermarket) available for the 2008 Suzuki SX4.

Last updated: 12 November 2026

Key specifications for the Suzuki SX4 2008–2011

Key types
smart keys, transponder keys, key shells, emergency blades and key blanks
Buttons
2-button
Blade profile
HU133
Part numbers
37172-62JV0 · 37145-63J60 · 37145-57J10
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Suzuki parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Suzuki SX4 2008 key

Smart key (push to start)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool. No working key is needed. Up to 4 remotes.

Programming steps

Program the remote without a tool

Needs: working key or emergency blade in the ignition, every remote / keyless-start fob the customer keeps

  1. Sit in the driver's seat, close all doors, make sure the driver's door is unlocked, insert the key (do not turn).
  2. Within 25 seconds: lock-unlock the driver's door lock 3 times, then lock once more.
  3. Still inside the 25 seconds: pull the key out and push it back in 4 times.
  4. Start the engine and let it run 3 seconds, then switch OFF (leave the key in): the buzzer sounds twice and the locks cycle, registration mode is on.
  5. Within 30 seconds press LOCK or UNLOCK on the remote; the buzzer sounds twice and the locks cycle.
  6. Repeat for each further remote within 30 seconds (up to 4).
  7. Remove the key or turn to ON to leave registration mode; test every remote.
Watch out: Register every remote in the same session. Remote / keyless-entry ID only: if the car will not start with the fob (keyless start), the immobiliser side needs a tool.
Program the remote without a tool(US / Canada cars)

Needs: working ignition key, every remote the customer keeps (up to 4)

  1. Close all doors with the key out of the ignition, then open the driver's door and leave it open.
  2. Insert the key, turn it to ON, and within 10 seconds turn it OFF and pull it out.
  3. Within 20 seconds close and open the driver's door 3 times (or press the door-jamb switch 3 times).
  4. Within 10 seconds insert the key, turn it to ON, then OFF and pull it out: the locks lock and unlock once (programming mode).
  5. Within 20 seconds press UNLOCK on the remote; the locks cycle to confirm.
  6. For each further remote run the routine again from step 1, then close the door and test every remote.
Watch out: The unit keeps 4 remotes: a fifth one pushes out the oldest. To drop a lost remote, program the remotes you keep until 4 registrations are made. Cars with the keyless start fob use a different routine; this one is for the separate remote (KBRTS005 type). This programs the remote only; the transponder key still has to start the car.

When the key changed

Smart key (push to start)

  • 2007 - 2013This yearChip: ID46315 MHzFCC: KBRTS003(US / Canada cars)Keyless start fob 37172-64J00 with emergency blade (SUZ20 keyway)
  • 2014 - 2022Chip: ID47433 MHz(GCC / Europe cars)S-Cross keyless key 37172-61M0x or 37172-68P1x; read the part number

Key with a blade (regular or flip)

  • 2006 - 2014This yearChip: ID46433 MHz(GCC / Europe cars)Diesel (Fiat engine) cars use an ID40 key; HU133 blade

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Suzuki SX4 2008–2011?

3 listings fit the Suzuki SX4 2008–2011: smart keys, transponder keys, key shells, emergency blades and key blanks, in 2-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which FCC IDs do Suzuki SX4 2008–2011 remotes carry?

The remotes listed for this car carry FCC ID TS001. Match it with the FCC ID printed on your original remote.

Which blade profile does the Suzuki SX4 2008–2011 key use?

The blades listed for this car: HU133.

Which tools program a Suzuki SX4 2008–2011 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Suzuki SX4 2008–2011 remote be programmed without a tool?

The remote is programmed on the car, without a tool. No working key is needed. Up to 4 remotes.