$2,250.00
In Stock
Genuine Microtronik · New
Microtronik Hexprog II Chip Tuning Tool Basic Set
OBD · Bench · Boot · TriCore DAP · BAM · JTAG · Nexus · NEC NBD · VFI · CAN FD · BMW ISN · 48-hour license included, then lease from USD 60.00 per day
15,000+
Cars, bikes, trucks and tractors
3 modes
OBD, bench and boot
220 MHz
32-bit RISC processor
3 years
Hardware warranty
⭐ The Microtronik Hexprog II Basic Set is a chip tuning tool for reading, writing, cloning and repairing ECUs and TCUs over OBD, on the bench and in boot mode. It reads and writes P-Flash, D-Flash, external flash and external EEPROM with automatic checksum correction, and reads the long ISN from BMW DME and DDE units, MD1 and MG1 included. Coverage runs to more than 15,000 cars, bikes, trucks and tractors across 70+ brands, with CAN FD built into both CAN channels. The Basic Set carries the full Hexprog II hardware with a 48-hour master license from registration, after which the master license is leased only when a job comes in: USD 60.00 for 1 day, USD 100.00 for 2 days or USD 200.00 for 7 days, with no annual fee. Microtronik covers the hardware with a 3-year warranty and 1 year of technical support.
⚙️ Key features
Master license, no slave files
Reads and writes files without slave dependencies or forced encryption.
Every connection method
OBD, bench, boot, BAM, TriCore DAP, JTAG, Nexus, NEC NBD, BDM and VFI from one unit.
Automatic checksum
Checksums are corrected after map changes on most supported ECUs.
BMW ISN reading
Long ISN from BMW and MINI DME/DDE from 2005, MD1 and MG1 included.
📸 Inside the Hexprog II Basic Set
01 · OVERVIEW
One unit for OBD, bench and boot work
Hexprog II is Microtronik's current-generation ECU and TCU tool for tuning, cloning and repair.
Vehicles - cars, bikes, trucks, tractors and boats
ECU makers - Bosch, Continental, Delphi, Marelli, Denso, Temic, GM, TRW, Valeo
Master version - unrestricted read and write of files
Same hardware in every set - Basic, Full and Lite sets change only the license
02 · MAIN UNIT
The Hexprog II interface
The main unit runs on a 32-bit RISC processor at 220 MHz with external SDRAM.
Status LEDs - four indicators on the face of the unit
Ports A to E - for the OBD, bench, boot and VFI cables
12-15 V input - bench power from the supplied adapter
USB port - connects to the Windows PC running HexProg II Tuner
CAN FD - native on both CAN channels for OBD, bench and boot
03 · OBD CABLE
OBD cable
Connects Hexprog II to the vehicle's diagnostic port for in-car work.
Map area read and write - tuning without removing the ECU
12 V and 24 V vehicles - cars and trucks from the same cable
Virtual Read - on supported ECUs, based on the ECU part number
Extra OBD jobs - VIN change, coding backup and restore, read and erase fault codes
04 · BENCH CABLES
Bench cable set
Four sets of wires for connecting the ECU on the bench by its wiring diagram.
CAN BUS wires - communication with the ECU
Signal wires - boot and control signals
Ground wires - common ground for the ECU
Power wires - feed the ECU from the Hexprog II supply
05 · BOOT CABLES
MPCxx / BDM and JTAG / BDM cables
Ribbon cables for boot mode on ECUs that need a direct PCB connection.
MPCxx / BDM cable - boot mode read and write on MPCxx ECUs, with a ribbon for BDM frames
Multi-coloured lead - for soldering directly to the ECU PCB
JTAG / BDM cable - rainbow ribbon for car and truck ECUs on MPC5xxx and SH72xx
Boot mode - used when bench communication is lost or the ECU requires it
06 · VFI ADAPTER
VFI adapter for locked MG1 / MD1
Unlocks secured TriCore MG1 and MD1 ECUs by Voltage Fault Injection.
Permanent unlock - patched in boot mode on supported TriCore 2xx MCUs
Bench mode afterwards - no need to reopen the ECU for later jobs
Automatic detection - locked, unlocked or no lock required
BMW MGD1 - read and written directly on the bench, no VFI step needed
07 · USB CABLE
Shielded USB cable
High-speed, noise-shielded cable between the PC and Hexprog II.
PC link - used in every mode
Noise shielding - ferrite-filtered for clean data transfer
USB A to USB B - standard connectors on both ends
Updates - the software updates the tool through this link
08 · POWER SUPPLY
14 V 3 A power adapter
A custom Microtronik supply that powers the ECU for bench and boot work.
Output - 14 V, 3 A
Bench and boot modes - feeds the ECU off the vehicle
Live tracking - voltage and current show at the top of the software
Mains cord - supplied with the adapter
09 · THE SET
Everything in the Basic Set
The Basic Set carries the full Hexprog II hardware.
Main unit - Hexprog II interface
Cables - OBD, USB, bench set, MPCxx / BDM and JTAG / BDM
VFI adapter - for secured MG1 and MD1
Power adapter - 14 V, 3 A
License - 48 hours from registration, then lease per job
10 · ON THE BENCH
Bench read with full control
The Tuner software shows the vehicle, engine, ECU and MCU before any read.
Internal flash and internal EEPROM - chosen separately with a toggle
Backup and restore - full .bak file for cloning to a donor ECU
Wiring diagram - one tap from the ECU page
Checksum: Auto - set per job in Settings
11 · BY OBD
OBD functions in one screen
In OBD mode the tool reads and writes the ECU without taking it out of the car.
Fault codes - read and erase
Read and write coding - back up the coding before a write
Identify and Virtual Read - ECU identification and fast virtual read
Write - progress bar shows each write in percent
12 · ECU IDENTIFICATION
ECU details before the read
Identify shows part, hardware and software numbers and the VIN before reading.
Identify - reads the ECU identification over OBD
Part, hardware and software numbers - check the file matches the ECU
VIN - stored VIN shown from the ECU
Save - keeps the identification with the job
13 · IN THE VEHICLE
Tuning through the OBD port
The ECU stays in the car while the laptop runs the job.
OBD cable to the DLC - no wiring diagram needed
Restore stock maps - original files can be written back from the server
Auto checksum - corrected before the write
Online services - run from the Hexprog Portal
14 · ON THE WORKBENCH
Bench and boot on the workbench
Bench mode connects to the ECU connector. Boot mode opens the cover for PCB access.
Bench mode - no need to open the ECU
Boot mode - recovery and access for protected ECUs
Clone button - copies data without changing the TriCore password
Individual data - read or write internal EEPROM, internal flash or external flash on its own
15 · BMW ISN
Long ISN from BMW DME and DDE
The ISN read comes from Microtronik's Autohex II BMW tools.
Full long ISN - BMW and MINI DME and DDE from 2005 to current
MD1 and MG1 - including F and G series
Bench or boot - with an ECU info button
VIN - displayed during the ISN read
💎 Benefits
Pay only when there is a job
No annual fee and no hidden charges. Lease the master license for 1, 2 or 7 days from USD 60.00.
No adapter collection to build
The cables and adapters for OBD, bench, boot and VFI work come in the set.
Clone used ECUs
Back up the original, clone to a donor and keep the TriCore password intact.
Upgrade path
Buy the permanent license later to move the same hardware to Full Set.
👥 Who it's for
Occasional ECU and TCU jobs
General repair shops that tune or clone a few units a month.
Automotive locksmiths
ECU cloning and BMW ISN reading next to key programming work.
Truck and bike workshops
24 V OBD vehicles, bikes and tractors from the same unit.
ECU repair specialists
Boot mode, VFI unlock and individual memory reads for damaged ECUs.
🧰 Supported coverage
Check coverage first: find the vehicle or the ECU in the supported lists below, then open it in HexProg II Tuner to see which modes are active before quoting the job. The software list is the current one, the PDFs are version 1.0.133.
📦 What's included
📋 Specifications
📊 Hexprog II Basic vs Full vs Lite
Microtronik's three Hexprog II sets use the same hardware. Only the license changes.
Note: the license is one master license. It cannot be split into cars, trucks or bikes.
📊 Hexprog vs Hexprog II
Microtronik's comparison of the first Hexprog and Hexprog II.
Note: Hexprog II is built for ECU cloning, chip tuning and ECU repair. Key and CAS work stays on other tools.
📊 Operating modes
How the three main modes compare in HexProg II Tuner.
