Skip to content

Dodge Durango 2009 Key Fob & Car Keys

Keys that fit the 2008–2009 Dodge Durango: remote keys and transponder keys, 2, 3 or 4 buttons, FCC ID M3N5WY783X, 0HT692427AA or IYZC01C, ID46 (HITAG 2) or PCF7941 chip, 315 MHz or 433 MHz. 16 compatible keys, remotes & shells (genuine and aftermarket) available for the 2009 Dodge Durango.

Last updated: 15 November 2026

Key specifications for the Dodge Durango 2008–2009

Key types
remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz and 433 MHz
Buttons
2-, 3-, 4- and 7-button
Transponder chip
ID46 (HITAG 2) · PCF7941 · CN3 cloning chip
Part numbers
For Mopar 05175817AA · For Mopar 56038768AA
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Dodge parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Dodge Durango 2009 key

Key with a blade (regular or flip)

3 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    PIN read function
    • Add key
    • Remote
    PIN read function

All keys lost is listed by OBDSTAR Key Master G3 and XTOOL X100 PAD3 / X100 MAX. Lonsdor K518 lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working keys, new blank transponder key cut to the vehicle

  1. Cut the new (never programmed) transponder key to the ignition; have two different keys that already start the vehicle.
  2. Insert the first working key and turn to ON for at least 3 but no more than 15 seconds, then turn OFF and remove it.
  3. Within 15 seconds insert the second working key and turn to ON; after about 10 seconds a chime sounds and the security light flashes. Turn OFF and remove it.
  4. Within 60 seconds (stay under 50 to be safe) insert the new blank key and turn to ON.
  5. After about 10 seconds a single chime sounds, the light stops flashing, stays on about 3 seconds and goes off: the key is learned.
  6. For each further key start again from step 2.
Watch out: Needs two different working keys; with one key or none use a tool (it reads the PIN). The new key must be blank: a key already learned to another vehicle is refused. Up to eight keys. On a remote head key or Fobik the remote learns in the same procedure.
Add key - on the car(US / Canada cars)

Needs: Two working remote keys available, two working programmed remote keys, the new remote key cut to the car

  1. Insert the first working key and turn the ignition ON for 5 seconds without cranking, then OFF and pull it out.
  2. Within 5 seconds, insert the second working key and turn ON. Within 10 seconds the security light flashes and a chime sounds (some cars only flash).
  3. Turn OFF and pull the second key out.
  4. Within 5 seconds, insert the new cut key and turn ON. Within 10 seconds a chime sounds and the security light goes out: the key is programmed.
  5. Turn OFF, pull the key and test the key and its remote.
Watch out: Only for cars built in the USA. Each key change must happen within 5 seconds.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Remote
    PIN read function

Without a tool

The remote is programmed on the car, without a tool. Up to 6 remotes.

When the key changed

Smart key (push to start)

  • 2014 - 2020Chip: ID46433 MHzFCC: M3N-40821302Hitag2 smart key (RF hub).

Key with a blade (regular or flip)

  • 2001 - 2003Chip: 4D-64Blade: Y160Sentry Key (SKIM) optional on this body.
  • 2004 - 2009This yearChip: ID46Blade: Y164Remote head key (SKREEM). No 2010 Durango was built.
  • 2011 - 2013Chip: ID46Fobik: the fob goes into the dash slot and turns, no blade.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Dodge Durango 2008–2009?

16 listings fit the Dodge Durango 2008–2009: remote keys, transponder keys, key shells and emergency blades, in 2-, 3-, 4- and 7-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Dodge Durango 2008–2009 remote use?

Listings for the Dodge Durango 2008–2009 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Dodge Durango 2008–2009 key use?

The listings for this car carry: ID46 (HITAG 2) · PCF7941 · CN3 cloning chip. Check the chip in each listing's specifications.

Which FCC IDs do Dodge Durango 2008–2009 remotes carry?

The remotes listed for this car carry FCC ID 0HT692427AA, IYZC01C, K0BDT04A and M3N5WY783X. Match it with the FCC ID printed on your original remote.

Which tools program a Dodge Durango 2008–2009 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Lonsdor K518 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Dodge Durango 2008–2009 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 6 remotes.